兰炭煤气发电机组使用的时候，如何防止兰炭煤气发电机组出现漏油、作为发电机厂家，让小编带大家共同了解一下防止兰炭煤气发电机组漏油的技巧!

　　How to prevent oil leakage of Lantan gas generator set when using it? As a generator manufacturer, let me take you to understand the techniques to prevent oil leakage of Lantan gas generator set!

　　1、粘补胶治漏法。油箱、水箱、油管、水管因决裂或砂眼、气孔等引起小渗漏，可用粘补胶涂改在清洗洁净的破害处即可。

　　1. Adhesive repair method for treating leaks. Oil tanks, water tanks, oil pipes, and water pipes may experience minor leaks due to rupture or sand holes, air holes, etc. They can be repaired with adhesive and cleaned to prevent damage.

　　2、加垫治漏法。兰炭煤气发电机组里的油管接头防漏垫圈处漏油，可在防漏垫圈的两端加一层双面润滑的薄塑料垫，用力拧紧即可防漏。

　　2. Add padding to treat leaks. The oil pipe joint leak proof gasket in the Lantan gas generator set leaks oil. A thin plastic pad with double-sided lubrication can be added to both ends of the leak proof gasket and tightened firmly to prevent leakage.

　　3、以抽治漏法。兰炭煤气发电机组的油箱底壳、气红苏、齿轮室养、曲轴箱后萧等多处纸垫渗漏时，若纸垫无缺、接合面清洁，可在纸垫双面林上一层黄油，拧紧螺栓即可防漏;如换新纸垫，把新纸垫放在柴油中浸泡10分

　　3. Using the method of extracting and treating leaks. When there are leaks in the oil tank bottom shell, gas red Su, gear room maintenance, crankcase rear Xiao and other paper pads of the Lantan gas generator set, if the paper pads are intact and the joint surface is clean, a layer of butter can be applied to both sides of the paper pads, and the bolts can be tightened to prevent leakage; If replacing the paper pad, soak it in diesel for 10 minutes

　　钟后取出擦净，在接合面上抹一层黄油再装上。

　　Take out the bell and wipe it clean. Apply a layer of butter on the joint surface before putting it back on.

　　4、漆片液治漏法。柴油机油箱、水箱、曲轴箱等接缝处渗漏，可将漆片在酒精里浸泡后，把漆片液涂改在清洗洁净的接缝外即可。5、厌胶治漏法。柴油机上的通气螺栓、双头螺栓等处出现渗漏时，可用厌氧胶涂改在清洗洁净的螺栓螺纹处或螺孔里，能很快固化构成薄膜，填充零件空隙;此法用于柴油机高压油管接头螺纹处治漏效果更好。

　　4. Lacquer slice liquid leak treatment method. If there is leakage at the joints of the diesel engine fuel tank, water tank, crankcase, etc., the paint can be soaked in alcohol and the paint liquid can be applied outside the cleaned joints. 5. The method of using adhesive to treat leaks. When there is leakage at the ventilation bolts, double headed bolts, etc. on the diesel engine, anaerobic adhesive can be used to modify the cleaned bolt threads or screw holes, which can quickly solidify into a thin film and fill the gaps in the parts; This method is more effective in treating leaks in high-pressure oil pipe joints of diesel engines.

　　6、液态密封胶治漏法。柴油机上出现固体垫困缺陷而构成的界面性渗漏和破坏性渗漏时，用液态密封胶涂改在清洗洁净的固体垫园结合面上，固化后构成均匀、稳定、连续黏附的可剥性薄膜垫园，可防渗漏。

　　6. Liquid sealant leakage treatment method. When there is interface leakage and destructive leakage caused by solid gasket entrapment defects on diesel engines, liquid sealant is used to modify the joint surface of the cleaned solid gasket. After curing, it forms a uniform, stable, and continuously adhered peelable film gasket, which can prevent leakage.

　　7、只度康年胶治漏法、柴油机的轴与轴弃、轴承与轴承座、烟与烟瘁、自紧油、填料等处渗漏时，可用尺磨康复胶涂改在清洗洁净的协作件磨损部位，固化后构成耐磨、机械强度较高的薄膜层，再进行机加工康复零件的几何形状和协作精度，可解决渗漏

　　7. When leakage occurs in areas such as shafts and shafts of diesel engines, bearings and bearing seats, smoke and exhaust, self tightening oil, fillers, etc., only the Kangnian adhesive treatment method can be used. A ruler can be used to grind and repair the adhesive to clean the worn parts of the cooperative parts. After curing, a wear-resistant and mechanically strong thin film layer can be formed, and then the geometric shape and cooperation accuracy of the parts can be repaired by machining, which can solve the problem of leakage

　　本文由   兰炭煤气发电机组    友情奉献.更多有关的知识请点击  http://www.zhongtuopower.cn/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from the Lantan Gas Generator Unit For more related knowledge, please click http://www.zhongtuopower.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.